®2014 MAXIMAOWNER’S MANUALFor your safety, read carefully and keep in this vehicle.2014 NISSAN MAXIMA A35-D Printing : July 2013 (13)Publicatio
1. Engine hood (P. 3-17)2. Windshield wiper and washer switch(P. 2-28)3. Windshield (P. 8-20)4. Moonroof (if so equipped) (P. 2-46)5. Power windows (P
This indicator means that the engine will start bypushing the push-button ignition switch with thebrake pedal depressed.NISSAN Intelligent Key® insert
Your vehicle has two types of security systems:● Vehicle security system● NISSAN Vehicle Immobilizer SystemVEHICLE SECURITY SYSTEMThe vehicle security
The alarm is activated by:● opening the door or trunk lid without usingthe key or Intelligent Key (even if the door isunlocked by releasing the door i
Security indicator lightThe security indicator light blinks whenever theignition switch is placed in the OFF, LOCK or ACCposition. This function indic
CAUTION● Do not operate the washer continuouslyfor more than 30 seconds.● Do not operate the washer if thewindshield-washer fluid reservoir isempty.●
XENON HEADLIGHTS (if soequipped)WARNINGcHIGH VOLTAGE● When xenon headlights are on, theyproduce a high voltage. To prevent anelectric shock, never att
HEADLIGHT CONTROL SWITCHLighting䊊1When turning the switch to the posi-tion, the front parking, tail, license plate andinstrument panel lights come on.
To turn on the autolight system:1. Place the headlight switch in the AUTO po-sition䊊1.2. Place ignition in the ON position.3. The autolight system aut
CAUTIONEven though the battery saver feature au-tomatically turns off the headlights after aperiod of time, you should turn the head-light switch to t
TURN SIGNAL SWITCHTurn signal䊊1Move the lever up or down to signal theturning direction. When the turn is com-pleted, the turn signal cancels automati
1. Rear window defroster switch (P. 2-29)2. Interior trunk lid release (P. 3-19)3. Trunk lid (P. 3-17)4. Vehicle loading (P. 9-12)5. Exterior trunk li
The front seats are warmed by built-in heaters.The switch is located on the center console.1. Start the engine.2. Push the LO or HI position of the sw
The climate controlled seat warms up or coolsdown the front seat by blowing warm or cool airfrom the surface of the seat. The climate controlswitch is
The heated steering wheel system is designed tooperate only when the surface temperature of thesteering wheel is below 68°F (20°C).Push the heated ste
The power outlets are for powering electricalaccessories such as cellular telephones. Theyare rated at 12 Volt, 120 W (10A) maximum.The power outlets
SEATBACK POCKETSThe seatback pockets are located on the back ofthe driver’s and passenger’s seats. The pocketscan be used to store maps.SUNGLASSES HOL
CUP HOLDERSCAUTION● Avoid abrupt starting and braking whenthe cup holder is being used to preventspilling the drink. If the liquid is hot, itcan scald
Soft bottle holderCAUTION● Do not use bottle holder for any otherobjects that could be thrown about inthe vehicle and possibly injure peopleduring sud
Lower halfPull up on the passenger’s side latch to open thelower half of the console box. A power outlet islocated inside the console box and there is
To install a cargo net, attach the net to the retain-ers.To remove a cargo net, detach the net from theretainers.POWER WINDOWSWARNING● Make sure that
Driver’s side power window switchThe driver’s side control panel is equipped withswitches to open or close all of the windows.To open a window, push t
1. Interior trunk access (P. 1-5)2. Moonroof (if so equipped) (P. 2-46)3. Sun visors (P. 3-24)4. Interior lights, illuminated entry (P. 2-50)5. HomeLi
Automatic operationTo fully open a window equipped with automaticoperation, press the window switch down to thesecond detent and release it; it need n
POWER MOONROOFThe moonroof will only operate when the ignitionswitch is placed in the ON position. The powermoonroof is operational for a period of ti
When closing:If the control unit detects something caught in themoonroof as it moves to the front, the moonroofwill immediately open backward.When til
Sliding the moonroofTo slide the moonroof:● To fully open the moonroof, push the switch䊊1toward the open position until it reachesthe second detent. I
SunshadeTo open the sunshade:● To fully open the sunshade, push the switch䊊1toward the open position until it reachesthe first detent.● To fully open
CAUTION● Do not place objects (such as newspa-pers, handkerchiefs, etc.) on the screeninlet port. Doing so may entangle theseobjects in the screen whe
NOTE:The footwell and doorstep lights illuminatewhen the driver and passenger doors areopened regardless of the interior lightswitch position. These l
Models without moonroofWIC1494Models with moonroofWIC1494Models with dual panel moonroofLIC14092-52 Instruments and controls
To turn the map lights on, press the switches. Toturn them off, press the switches again.CAUTIONDo not use for extended periods of timewith the engine
WARNING● Do not use the HomeLink® UniversalTransceiver with any garage dooropener that lacks safety stop and re-verse features as required by federals
1. Side and center vents (P. 4-28)2. Headlight/fog light (if so equipped)/turnsignal switch (P. 2-30)3. Steering wheel switch for audio controland Blu
3. Press and hold the programmedHomeLink® button and observe the indica-tor light.● If the indicator light䊊1issolid/continuous, programming iscomplete
press and hold the desired HomeLink® but-ton while you press and re-press (“cycle”)your hand-held transmitter every two sec-onds until the frequency s
2. The indicator light will begin to flash after20 seconds. Without releasing theHomeLink® button, proceed with “Pro-gramming HomeLink®” - Step 1.For
MEMO2-58 Instruments and controls
3 Pre-driving checks and adjustmentsKeys...3-2NISSAN Intelligent Key® ...3-2NISSAN Vehi
1. Two Intelligent Keys2. Mechanical keys with built-in transpon-der chip (inside Intelligent Keys)3. Key number plateNISSAN INTELLIGENT KEY®Your vehi
Mechanical keyThe Intelligent Key contains the mechanical key,which can be used in case of a discharged bat-tery.To remove the mechanical key, release
Any key that is not given to your dealer at the timeof registration will no longer be able to start yourvehicle.CAUTIONDo not allow the immobilizer sy
Opening and closing windowsThe driver’s door key operation allows you toopen and close windows equipped with auto-matic operation at the same time.● T
Lockout protectionWhen the power door lock switch (driver’s orfront passenger’s side) is moved to the lockposition with the Intelligent Key in the por
24. Vehicle Dynamic Control (VDC) OFFswitch (P. 2-37)Outside mirror controls (P. 3-27)Heated steering wheel switch (if soequipped) (P. 2-37)Trunk lid
WARNING● Radio waves could adversely affectelectric medical equipment. Those whouse a pacemaker should contact theelectric medical equipment manufac-t
CAUTIONListed below are conditions or occur-rences which will damage the IntelligentKey:● Do not allow the Intelligent Key, whichcontains electrical c
If the Intelligent Key is too close to the door glass,handle or rear bumper, the request switches maynot function.When the Intelligent Key is within t
NISSAN INTELLIGENT KEY®OPERATIONYou can lock or unlock the doors without takingthe Intelligent Key out of your pocket or bag.When you carry the Intell
● Doors do not lock with the door handlerequest switch with the Intelligent Key insidethe vehicle and a beep sounds to warn you.However, when an Intel
All doors will be locked automatically unless oneof the following operations is performed within60 seconds after pushing the request switch.● Opening
When all doors are locked and the trunk lid isclosed with the Intelligent Key inside the trunk,the outside buzzer will sound and the trunk willopen.HO
Unlocking doors1. Press the button on the IntelligentKey.2. The hazard warning lights flash once.3. Press thebutton again within 60 sec-onds to unlock
Using the panic alarmIf you are near your vehicle and feel threatened,you may activate the panic alarm to call attentionby pressing and holding thebut
TROUBLESHOOTING GUIDEVerify the location of all Intelligent Keys that areprogrammed for the vehicle. If another IntelligentKey is in range or inside t
1. Power steering fluid reservoir (P. 8-13)2. Engine oil filler cap (P. 8-10)3. Brake fluid reservoir (P. 8-14)4. Air cleaner (P. 8-19)5. Fuse block (
䊊1Pull the hood lock release handle locatedbelow the driver side instrument panel. Thehood will spring up slightly.䊊2Push the lever at the front of th
OPENER OPERATIONWARNING● Do not drive with the trunk lid open. Thiscould allow dangerous exhaust gasesto be drawn into the vehicle. See “Ex-haust gas”
INTERIOR TRUNK LID RELEASEWARNINGClosely supervise children when they arearound cars to prevent them from playingand becoming locked in the trunk wher
OPENING THE FUEL-FILLER DOORThe fuel-filler door automatically unlocks whenthe driver’s door is unlocked.1. Unlock the fuel-filler door using one of t
CAUTION● Do not use E-15 or E-85 fuel in yourvehicle. For further information see the“Fuel Recommendation” in the “Techni-cal and consumer information
Loose Fuel Cap warningThe LOOSE FUEL CAP warning appears in thevehicle information display when the fuel-fillercap is not tightened correctly after th
MANUAL OPERATION (if soequipped)Tilt and telescopic operationPull the lock lever䊊1all the way towards you:● Adjust the steering wheel forward or back-
䊊1To block glare from the front, swing down thesun visor.䊊2To block glare from the side, remove the sunvisor from the center mount and swing thevisor
AUTOMATIC ANTI-GLAREREARVIEW MIRRORThe inside mirror is designed so that it automati-cally dims during night time conditions and ac-cording to the int
Type B and Type CThe indicator light䊊2will illuminate when theautomatic anti-glare feature is operating.To turn off the automatic anti-glare feature,
WarninglightName PageorAnti-lock BrakingSystem (ABS) warn-ing light2-11orBrake warning light 2-11Charge warninglight2-11Engine oil pressurewarning lig
OUTSIDE MIRRORSThe outside mirror remote control will operateonly when the ignition switch is in the ACC or ONposition.Move the small switch䊊1to selec
NOTE:If the outside mirror control switch is in theneutral position, neither mirror will turndownward when the shift lever is moved toR (Reverse).Move
MEMORY STORAGE FUNCTIONTwo positions for the driver’s seat, steering col-umn, and outside mirrors can be stored in theautomatic drive positioner memor
1. Connect the battery cable or replace thefuse.2. Open and close the driver’s door more than2 times with the ignition switch in the LOCKposition.Once
4 Monitor, climate, audio, phone and voicerecognition systemsControl panel buttons — color screen withoutNavigation System (if so equipped) ...
FM/AM radio with compact disc (CD)changer (if so equipped) ...4-51FM/AM/SAT radio with compact disc (CD)player (if so equipped) ..
NISSAN Voice Recognition Standard Mode ...4-119Using the system ...4-121Before starting ...4-1
WARNING● Positioning of the heating or air condi-tioning controls and display controlsshould not be done while driving in or-der that full attention m
CAUTION● The glass display screen may break if itis hit with a hard or sharp object. If theglass screen breaks, do not touch it.Doing so could result
HOW TO SELECT MENUS ON THESCREENVehicle functions are viewed on the center dis-play screen in menus. Whenever a menu selec-tion is made or menu item i
MEMO0-10 Illustrated table of contents
Menu Item ResultFuel Economy Displays Fuel Economy menu.Distance to Empty Displays an estimation of the distance that the vehicle can be driven before
HOW TO USE THE SETTINGBUTTONPress the SETTING button. This screen displaysand adjusts various settings and functions thatare available for your vehicl
Menu Item ResultAudio See “Audio system” in this section for more information.Display Adjusts the settings for the display screen.Brightness/Contrast
Menu Item ResultComfort & Convenience Select the “Others” key using the NISSAN controller, then select the “Comfort” key. The Comfort settings scr
1. ZOOM OUT button*2. STATUS button (P. 4-15)3. DEST button*4. ROUTE button*5. NISSAN controller (P. 4-12)6. INFO button (P. 4-15)7. PHONE button**8.
HOW TO USE THE NISSANCONTROLLERUse the NISSAN controller to choose an item onthe display screen. Highlight an item on the dis-play using the main dire
Touch screen operationWith this system, the same operations as thosefor the NISSAN controller are possible using thetouch screen operation.Menu Item R
Touch screen maintenanceIf you clean the display screen, use a dry, softcloth. If additional cleaning is necessary, use asmall amount of neutral deter
HOW TO USE THE STATUSBUTTONThe STATUS button is used to display systeminformation. Three different split screens of infor-mation are available. Press
Menu Item ResultFuel Economy Displays Fuel Economy menu.Distance to Empty Displays an estimation of the distance that the vehicle can be driven before
1 Safety—Seats, seat belts andsupplemental restraint systemSeats . ...1-2Front power seat adjustment. . ...
HOW TO USE THE SETTINGBUTTONPress the SETTING button. This screen displaysand adjusts various settings and functions thatare available for your vehicl
Menu Item ResultOthers Select the “Others” key using the NISSAN controller. Voice Recognition, language and units setting screen will be displayed.Com
Menu Item ResultSelect Language Changes the language of the menus on the display screen. If you select the “Francais” key, French language screens wil
USING THE IMAGE VIEWERWhen a compatible portable storage device isplugged into the USB jack located in the centerconsole, compatible image files store
Viewing images in a slideshowTo view all of the images on the device in aslideshow, first enter the full screen mode whileviewing one of the images. T
When the shift lever is shifted into the R (Re-verse) position, the monitor display shows a rear-ward view from the vehicle.WARNING● The system is des
Vehicle width guide lines䊊5:Indicate the vehicle width when backing up.Predicted course lines䊊6:Indicate the predicted course when backing up.The pred
1. Visually check that the parking space is safebefore parking your vehicle.2. The rear view of the vehicle is displayed onthe screen䊊Awhen the shift
Backing up on a steep uphillWhen backing up the vehicle up a hill, the dis-tance guide lines and the vehicle width guidelines are shown closer than th
the hill is the place䊊B. Note that any object onthe hill is closer than it appears on the monitor.Backing up near a projecting objectThe predicted cou
WARNING● Do not ride in a moving vehicle whenthe seatback is reclined. This can bedangerous. The shoulder belt will notbe against your body. In an acc
the position䊊Aif the object projects over theactual backing up course.HOW TO ADJUST THE SCREENTo adjust the Display ON/OFF, Brightness, Tint,Color, Co
Adjust air flow direction by moving the ventslides.Open or close the vents by using the dial. Movethe dial toward theto open the vents ortoward theto
1. Temperature control buttons (driver’sside)2. AUTO climate control ON button3.(front defroster) button4.Air recirculation button5. MODE (manual air
NOTE:● Odors from inside and outside the vehiclecan build up in the air conditioner unit. Odorcan enter the passenger compartmentthrough the vent.● Wh
MANUAL OPERATIONFan speed controlTurn the fan speed control dial to manuallycontrol the fan speed.Press the AUTO button to return to automaticcontrol
1.Air recirculation button2. A/C (air conditioner) ON/OFF button3. MODE (manual air flow control) button4.Fresh air intake button5. Temperature contro
NOTE:● Odors from inside and outside the vehiclecan build up in the air conditioner unit. Odorcan enter the passenger compartmentthrough the vents.● W
MANUAL OPERATIONFan speed controlTurn the fan speed control dial to manuallycontrol the fan speed.Press the AUTO button to return to automaticcontrol
The air conditioner system in your NISSAN ve-hicle is charged with a refrigerant designed withthe environment in mind.This refrigerant does not harm t
Static and flutter: During signal interference frombuildings, large hills or due to antenna position(usually in conjunction with increased distancefro
Welcome to the growing family of new NISSANowners. This vehicle is delivered to you withconfidence. It was produced using the latesttechniques and str
FRONT POWER SEAT ADJUSTMENTOperating tips● The power seat motor has an auto-resetoverload protection circuit. If the motorstops during operation, wait
Compact disc (CD) player (modelswithout Navigation System)CAUTION● Do not force a compact disc into the CDinsert slot. This could damage the CDand/or
CD/DVD combination player (modelswith Navigation System)● Do not force a disc into the CD/DVDinsert slot. This could damage theCD/DVD player.● During
Region Invalid● The DVD is not for region 1 or allregions.● Use DVDs with a region code “1”,“ALL” or “1 included” for your DVDentertainment system. (T
CAUTION● Do not force the USB device into theUSB port. Inserting the USB devicetilted or up-side-down into the port maydamage the port. Make sure that
● The Bluetooth® audio may be stopped un-der the following conditions:● Receiving a call on the Hands-FreePhone System.● Checking the connection to th
Playback order:Music playback order of a CD with MP3 or WMAfiles is as illustrated.● The names of folders not containing MP3 orWMA files are not shown
Specification chart:Supported media CD, CD-R, CD-RW, USB 2.0Supported file systemsCD, CD-R, CD-RW, ISO9660 LEVEL1, ISO9660 LEVEL2, Romeo, Joliet* ISO9
Troubleshooting guide:Symptom Cause and CountermeasureCannot playCheck if the CD/USB device was inserted correctly.Check if the CD is scratched or dir
CD, DVD or USB with CompressedAudio Files (models with NavigationSystem)The file types supported by this system are MP3,WMA, AAC/M4A and ATRAC3.Explan
Playback order:Music playback order of a CD, DVD or USBdevice with compressed audio files is as illus-trated.● The folder names of folders not contain
Seat lifter (driver’s seat)Push the front or rear end of the switch up ordown to adjust the angle and height of the seatcushion.Lumbar support (driver
Specification chart:Supported media CD, CD-R, CD-RW, DVD-ROM, DVD±R, DVD±RW, DVD±R DL, USB 2.0Supported file systemsCD, CD-R, CD-RW, DVD-ROM, DVD±R, D
Troubleshooting guide:Symptom Cause and CountermeasureCannot playCheck if the CD/DVD/USB device was inserted correctly.Check if the CD/DVD is scratche
Compressed Video Files (models withNavigation System)Explanation of terms:● DivX – DivX refers to the DivX® codecowned by Div, Inc. used for a lossy c
Requirements for Supporting Video Playback:Media CD, CD-R, CD-RW, DVD, DVD±R, DVD±RW, DVD±RW DL, USB 2.0 MemoryFile SystemsCD, CD-R, CD-RW, DVD,DVD±R,
1.CD eject button2. VOL/ON·OFF control knob3. Station and CD select (1 - 6) buttons4. LOAD CD button5. TUNE/FOLDER and AUDIO controlknob (Bass, Treble
Audio control knobAudioBass Adjusts the bass to the desired level.Treble Adjusts the treble to the desired level.Balance Adjusts the balance to the de
MP3 display modeTo change the text displayed when listening to aCD with MP3s and ID3 tags, press theDISP/CLOCK button. The DISP/CLOCK buttonwill scrol
Compact disc (CD) changer operationPlace the ignition switch in the ACC or ONposition and press the LOAD button, then pressone of the CD insert (1 – 6
1 Disc Repeat: The disc that is currently playingwill be repeated.1 Track Repeat: The track that is currently playingwill be repeated.1 Folder Repeat:
1.CD eject button2. VOL/ON·OFF control knob3. Station select (1 - 6) buttons4. TUNE/FOLDER and AUDIO controlknob (Bass, Treble, Fade and Balance)5. AU
Thigh extension (driver’s side only, ifso equipped)Pull up and hold the lever to extend the frontportion to the desired position.FOLDING REAR SEAT (if
Audio control knobAudioBass Adjusts the bass to the desired level.Treble Adjusts the treble to the desired level.Balance Adjusts the balance to the de
CD/MP3 display modeWhile listening to a CD or an MP3/WMA CD,certain text might be able to be displayed (whenCD encoded with text is being used).Depend
XM band select:Pressing the AUX button will change the band asfollows:USB → XM1* → XM2* → XM3* → AUX → USB(satellite, if so equipped)When the AUX butt
When the “Text” key is selected with the NISSANcontroller on the display while the radio is playing,additional information is displayed on the screen.
CD EJECT button:When thebutton is pressed with the com-pact disc loaded, the compact disc will beejected.When thebutton is pressed while thecompact di
AUX settingsSelect the “Settings” key using the NISSAN con-troller and press the ENTER button.Choose one of the display modes by selectingthe “” key o
1.CD eject button2. VOL/ON·OFF control knob3. Station select (1 - 6) buttons4. TUNE/FOLDER and AUDIO controlknob (Bass, Treble, Fade and Balance)5. DI
Audio settingsAudioBass Adjusts the bass to the desired level.Treble Adjusts the treble to the desired level.Balance Adjusts the balance to the desire
Display album cover art:When an audio source encoded with albumcover art is played, the album cover art can bedisplayed on the screen. To toggle this
The FM stereo indicator STEREO will illuminateduring FM stereo reception. When the stereobroadcast signal is weak, the radio will automati-cally chang
● When returning the seatbacks to theupright position, be certain they arecompletely secured in the latched posi-tion. If they are not completely secu
Menu (SiriusXM Satellite Radio, if soequipped)Select the “Menu” key using the NISSAN control-ler or touchscreen to see a list of options:● Preset List
SEEK/CAT and TRACKbuttons:When the SEEK/CATbutton is pressedwhile a compact disc is playing, the track beingplayed returns to its beginning. Press sev
● Play ModeThis option allows you to alter the play pattern ofthe CD. Touch the key of the mode you wish toapply. The modes change the play pattern as
● Track ListThe tracks on the disc are displayed. Select thekey of a track name to begin playing that track.CD EJECT button:When thebutton is pressed
AUX settingsSelect the “Settings” key using the NISSAN con-troller.The display mode can be set to Normal, Wide orCinema. The volume setting can be set
CAUTION● Only operate the DVD while the vehicleengine is running. Operating the DVDfor extended periods of time with theengine OFF can discharge the v
NEXT/PREVIOUSCHAPTER:Select thekey to skip the chapter(s) of thedisc forward. Select thekey to skip thechapter(s) of the disc backward. The chapterswi
● CM Skip (DVD-VIDEO)Select the “CM Skip” key to choose thesetting time for CM backward and forwardoperations. Use the “+” or “-” key to choosea setti
CAUTION● Do not force the USB device into theUSB port. Inserting the USB devicetilted or up-side-down into the port maydamage the port. Make sure that
USB INTERFACE (models withNavigation System)Connecting a device to the USB inputjackWARNINGDo not connect/disconnect or operate theUSB device while dr
Center armrestPull the armrest down until it rests on the seatcushion.FRONT SEAT HEAD RESTRAINTS/HEADRESTSWARNING● Head restraints/headrests supplemen
Audio file operationDISC•AUX button:Place the ignition switch in the ON or ACCposition and press the DISC•AUX button toswitch to the USB input mode. I
● Folder List/Track ListDisplays the folder or track list. The “MoviePlayback” key is also displayed in this listscreen and enables you to switch to t
● Previous Chapter/Rewind:Select thekey to skip the chapter(s)of the disc backward. The chapters will goback the number of times the key is selected.P
iPod®* PLAYER OPERATIONWITHOUT NAVIGATION SYSTEM (ifso equipped)Connecting iPod®WARNINGDo not connect/disconnect or operate theUSB device while drivin
Audio main operationPlace the ignition switch in the ACC or ONposition. Press the AUX button repeatedly toswitch to the iPod® mode.If the system has b
● Albums● Artists● Genres● Composers● AudiobooksThe following keys shown on the screen are alsoavailable:● MENU: returns to the previous screen.●: pla
While connected to the vehicle, the iPod® canonly be operated by the vehicle audio controls.To disconnect the iPod® from the vehicle, re-move the USB
Interface:The interface for iPod® operation shown on thevehicle center display is similar to the iPod®interface. Use the NISSAN controller and theBACK
When the SEEK/CAT button orTRACK button is pressed for more than 1.5 sec-onds while the iPod® is playing, the iPod® willplay while fast forwarding or
Connecting Bluetooth® audioTo connect your Bluetooth® audio device to thevehicle, follow the procedure below:1. Press the SETTING button on the contro
● Adjustable head restraints/headrests havemultiple notches along the stalk to lock themin a desired adjustment position.● The non-adjustable headrest
Audio main operationTo switch to the Bluetooth® audio mode, pressthe DISC•AUX button repeatedly until theBluetooth® audio mode is displayed on thescre
5. A list of the connected Bluetooth® audioplayers is displayed. Select the name of thedevice you wish to edit.6. The Device Name and Device Address a
● A new disc may be rough on the inner andouter edges. Remove the rough edges byrubbing the inner and outer edges with theside of a pen or pencil as i
SOURCE select switchPush the source select switch to change themode in the following sequence:Models without Navigation System:AM → FM1 → FM2 → XM1 →
AUX:● Press the ENTER button to show the AUXMenu.ANTENNAWindow antennaThe antenna pattern is printed inside the rearwindow.CAUTION● Do not place metal
WARNING● Use a phone after stopping your vehiclein a safe location. If you have to use aphone while driving, exercise extremecaution at all times so f
phone module when the ignition switch is placedin the ON position with the previously connectedcellular phone turned on and carried in the ve-hicle.Yo
IC Regulatory information– Operation is subject to the following two con-ditions: (1) this device may not cause interfer-ence, and (2) this device mus
● You can cancel a command when the sys-tem is waiting for a response by saying,“Cancel” or “Quit.” The system announces“Cancel” and ends the VR sessi
CONTROL BUTTONSThe control buttons for the Bluetooth® Hands-FreePhone System are located on the steering wheel.PHONE/SENDPress thebutton to initiate a
RemovableUse the following procedure to remove the headrestraints/headrests.1. Pull the head restraint/headrest up to thehighest position.2. Push and
Connecting procedureNOTE:The connecting procedure must be per-formed when the vehicle is stationary. If thevehicle starts moving during the procedure,
Receiving a callWhen you hear the ring tone, press thebutton on the steering wheel.Once the call has ended, press thebuttonon the steering wheel.NOTE:
“Redial”䊊DUse the Redial command to call the last numberthat was dialed.The system acknowledges the command, re-peats the number and begins dialing.If
For phones that do not support automatic down-load of the phonebook (PBAP Bluetooth® pro-file), the “Phonebook” command is used to manu-ally add entri
For phones that support automatic download ofthe phonebook (PBAP Bluetooth® profile), the“Phonebook” command is used to manage en-tries in the vehicle
“Connect Phone”NOTE:The Add Phone command is not availablewhen the vehicle is moving.Main Menu“Connect Phone”“Add Phone”䊊A“Select Phone”䊊B“Delete Phon
10. The system will announce that voice adap-tation has been completed and the system isready.The VA mode will stop if:● Thebutton is pressed for more
Operating tips● To enter manual control mode, start thevoice recognition system and tilt the tuning() switch up or down. The system willspeak ⬙Showing
TROUBLESHOOTING GUIDEThe system should respond correctly to all voicecommands without difficulty. If problems are en-countered, try the following solu
WARNING● Use a phone after stopping your vehiclein a safe location. If you have to use aphone while driving, exercise extremecaution at all times so f
For non-adjustable head restraint/headrestMake sure the head restraint/headrest is posi-tioned so the lock knob is engaged in the notchbefore riding i
phone module when the ignition switch is placedin the ON position with the connected cellularphone turned on and carried in the vehicle.You can regist
REGULATORY INFORMATIONFCC Regulatory information– CAUTION: To maintain compliance withFCC’s RF exposure guidelines, use only thesupplied antenna. Unau
CONNECTING PROCEDURETo connect a Bluetooth® device, use one of thefollowing methods:● Press the “Phone” button on the controlpanel or thebutton on the
VEHICLE PHONEBOOKThis vehicle has two phonebooks available foryour use. Depending on your phone, the systemmay automatically download your entire cell
Press the button on the steering wheel orthe “Phone” button on the control panel and thenselect the ⬙Vehicle Phonebook⬙ key. Next, selectthe desired e
HANDSET PHONEBOOKMany phones will support an automatic down-load of the cellular phone’s phonebook. Sincethis method allows for up to 1000 numbers to
MAKING A CALLPress the button on the steering wheel orthe “Phone” button on the control panel. The⬙Phone⬙ screen will appear on the display. Selectone
RECEIVING A CALLWhen you hear a phone ring, the display willchange to phone mode. To receive a call, followone of the procedures listed below:Menu Ite
DURING A CALLThere are some options available during a call.Select one of the following displayed on thescreen, if necessary:Menu Item ResultHang Up F
PHONE SETTINGSTo set up the Bluetooth Hands-Free Phone Sys-tem to your perferred settings, press the SET-TING button on the control panel and select t
REAR SEAT HEAD RESTRAINTS/HEADRESTSWARNING● Head restraints/headrests supplementthe other vehicle safety systems. Theymay provide additional protectio
BLUETOOTH SETTINGSTo set up the Bluetooth Hands-Free Phone Sys-tem to your preferred settings, press the SET-TING button on the control panel and sele
CALL VOLUMEAdjusting the incoming or outgoing call volumemay improve clarity if reception between callers isunclear. To access the volume settings, pr
NISSAN Voice Recognition allows hands-freeoperation of the systems equipped on this ve-hicle, such as phone and vehicle information.There are two voic
Menu Item ResultGetting Started The following message will appear: ⬙With voice recognition, you can use voice commands to control navigation, audio, p
USING THE SYSTEMInitializationWhen the ignition switch is placed in the ONposition, NISSAN Voice Recognition is initialized,which takes a few seconds.
Operating tips● Say a command after the tone. Voice com-mands cannot be accepted when the iconis.● Commands that are available are alwaysshown on the
Standard Mode command listCategory Commands:COMMAND ACTIONPhone Displays Phone function commands.Navigation Displays Navigation function commands.Info
Vehicle Information Commands:COMMAND ACTIONFuel Economy Displays Fuel Economy information.Maintenance Displays Maintenance information.Traffic Informa
Voice command examplesSome basic voice command examples are de-scribed here.For navigation system commands, see the sepa-rate Navigation System Owner’
● Do not add a “1” in front of the area codewhen speaking phone numbers.● If the system does not recognize your com-mand, please try repeating the com
Adjustable head restraint/headrestcomponents1. Removable head restraint/headrest2. Multiple notches3. Lock knobs4. StalksNon-adjustable head restraint
Please note that in this mode the recognitionsuccess rate may be affected as the number ofavailable commands and ways of speaking eachcommand are incr
Alternate Command Mode command listPhone Commands:COMMAND ACTIONDial Number Makes a call to a spoken phone number up to 10 digits.Vehicle Phonebook Ma
COMMAND ACTIONBirdview Map Changes the Map display to Birdview.Planview Map Changes the Map display to a 2-dimensional view.North Up Changes the Map d
Displaying user guideYou can confirm how to use voice commands byaccessing a simplified User Guide, which con-tains basic instructions and tutorials f
USING THE SYSTEMInitializationWhen the ignition switch is placed in the ONposition, NISSAN Voice Recognition is initialized,which takes a few seconds.
Operating tips● Say a command after the tone. Voice com-mands cannot be accepted when the iconis.● If the command is not recognized, the sys-tem repea
Voice recognition settingsThe available settings for the NISSAN Voice Rec-ognition system, while in Alternate CommandMode, are described.1. Press the
SPEAKER ADAPTATION FUNCTIONThe Voice Recognition system has a function tolearn the user’s voice for better voice recognitionperformance. The system ca
Speaker Adaptation function settingsTo access the speaker adaptation function set-tings:1. Press the SETTING button on the controlpanel.2. Select the
TROUBLESHOOTING GUIDEThe system should respond correctly to all voicecommands without difficulty. If problems are en-countered, follow the solutions g
MODIFICATION OF YOUR VEHICLEThis vehicle should not be modified.Modification could affect itsperformance, safety or durability, andmay even violate go
Install1. Align the head restraint/headrest stalks withthe holes in the seat. Make sure the headrestraint/headrest is facing the correct di-rection.2.
5 Starting and drivingPrecautions when starting and driving...5-2Exhaust gas (carbon monoxide) ...5-2Three-way catalyst...
WARNING● Do not leave children or adults whowould normally require the assistanceof others alone in your vehicle. Petsshould also not be left alone. T
CAUTION● Do not use leaded gasoline. Depositsfrom leaded gasoline will seriously re-duce the three-way catalyst’s ability tohelp reduce exhaust pollut
Additional information:● The TPMS does not monitor the tirepressure of the spare tire.● The TPMS will activate only when the vehicleis driven at speed
● Replacing tires with those not originallyspecified by NISSAN could affect theproper operation of the TPMS.● Do not inject any tire liquid or aerosol
OFF-ROAD RECOVERYIf the right side or left side wheels unintentionallyleave the road surface, maintain control of thevehicle by following the procedur
DRINKING ALCOHOL/DRUGS ANDDRIVINGWARNINGNever drive under the influence of alcoholor drugs. Alcohol in the bloodstream re-duces coordination, delays r
The ignition lock is designed so that the ignitionswitch position cannot be switched to OFF untilthe shift lever is moved to the P (Park) position.Whe
OFF:The ignition switch is in the OFF position whenthe engine is turned off using the ignition switch.No lights will illuminate on the ignition switch
To remove the Intelligent Key from the port, pushthe ignition switch to the LOCK position and pullthe Intelligent Key out of the port䊊C.NOTE:The Intel
To raise the head restraint/headrest,pull it up.Make sure the head restraint/headrest is posi-tioned so the lock knob is engaged in the notchbefore ri
● Make sure the area around the vehicle isclear.● Check fluid levels such as engine oil, cool-ant, brake fluid, and window washer fluid asfrequently a
NOTE:Care should be taken to avoid situationsthat can lead to potential battery dischargeand potential no-start conditions such as:1. Installation or
CAUTIONWhen stopping the vehicle on an uphillgrade, do not hold the vehicle by depress-ing the accelerator pedal. The foot brakeshould be used for thi
4. Stop the vehicle completely before shiftingthe shift lever to the P (Park) position.The CVT is designed so the foot brakepedal MUST be depressed be
R (Reverse):CAUTIONTo prevent transmission damage, use theP (Park) or R (Reverse) position only whenthe vehicle is completely stopped.Use the R (Rever
When the shift lever is shifted from D (Drive) tothe manual shift gate䊊Awith the vehicle stoppedor while driving, the transmission enters themanual sh
● CVT operation is limited to automatic drivemode when CVT fluid temperature is ex-tremely low even if manual shift mode isselected. This is not a mal
Accelerator downshift— in D (Drive) position and manualshift modeFor passing or hill climbing, depress the accel-erator pedal to the floor. This shift
To engage: Firmly depress the parking brake.To release:1. Firmly apply the foot brake.2. Move the shift lever to the P (Park) position.3. Firmly depre
To set cruising speed, accelerate the vehicle tothe desired speed, push the COAST/SET switchand release it. Take your foot off the acceleratorpedal. Y
● Do not attach anything to the headrestraint/headrest stalks. Doing socould impair Active Head Restraintfunction.The Active Head Restraint moves forw
CAUTIONDuring the first 1,200 miles (2,000 km),follow these recommendations to obtainmaximum engine performance and ensurethe future reliability and e
6. Plan for the Shortest Route● Utilize a map or navigation system to de-termine the best route to save time7. Avoid Idling● Shutting off your engine
WARNING● Do not stop or park the vehicle overflammable materials such as dry grass,waste paper or rags. They may igniteand cause a fire.● Safe parking
The power assisted steering uses a hydraulicpump, driven by the engine, to assist steering.If the engine stops or the drive belt breaks, youwill still
This procedure is described in the vehicle servicemanual and can be performed by a NISSANdealer.ANTI-LOCK BRAKING SYSTEM(ABS)WARNING● The Anti-lock Br
When the ABS senses that 1 or more wheels areclose to locking up, the actuator rapidly appliesand releases hydraulic pressure. This action issimilar t
The VDC system is automatically reset to onwhen the ignition switch is placed in the offposition then back to the on position.The computer has a built
FREEING A FROZEN DOOR LOCKTo prevent a door lock from freezing, apply de-icer through the key hole. If the lock becomesfrozen, heat the key before ins
● Whatever the condition, drive with cau-tion. Accelerate and slow down withcare. If accelerating or downshifting toofast, the drive wheels will lose
MEMO5-30 Starting and driving
WARNING● Every person who drives or rides in thisvehicle should use a seat belt at alltimes. Children should be properly re-strained in the rear seat
6 In case of emergencyEmergency engine shut off ...6-2Hazard warning flasher switch ...6-2Flat tire ...
To shut off the engine in an emergency situationwhile driving, perform the following procedure:– Rapidly push the push-button ignition switch 3consecu
TIRE PRESSURE MONITORINGSYSTEM (TPMS)This vehicle is equipped with the Tire PressureMonitoring System (TPMS). It monitors tire pres-sure of all tires
WARNING● Make sure the parking brake is securelyapplied and the CVT is shifted into P(Park).● Never change tires when the vehicle ison a slope, ice or
Remove the jack䊊1and wheel nut wrench䊊2from the tool box on the right side of the trunkcompartment.Remove the spare tire.Jacking up vehicle and removi
● Use the correct jack-up points. Neveruse any other part of the vehicle for jacksupport.● Never jack up the vehicle more thannecessary.● Never use bl
Installing the spare tireThe spare tire is designed for emergencyuse. See specific instructions under theheading “Wheels and tires” in the “Mainte-nan
To start your engine with a booster battery, theinstructions and precautions below must be fol-lowed.WARNING● If done incorrectly, jump starting canle
WARNINGAlways follow the instructions below. Fail-ure to do so could result in damage to thecharging system and cause personalinjury.1. If the booster
CAUTION● CVT models cannot be push-started ortow-started. Attempting to do so maycause transmission damage.● Do not push start this vehicle. Thethree-
WARNING● Always route the shoulder belt overyour shoulder and across your chest.Never put the belt behind your back,under your arm or across your neck
When towing your vehicle, all State (Provincial inCanada) and local regulations for towing must befollowed. Incorrect towing equipment could dam-age y
CAUTION● Never tow CVT models with the frontwheels on the ground or four wheels onthe ground (forward or backward), asthis may cause serious and expen
● Do not use the vehicle tie-downs to towor free a stuck vehicle.● Only use devices specifically designedfor vehicle recovery and follow themanufactur
MEMO6-14 In case of emergency
7 Appearance and careCleaning exterior ...7-2Washing ...7-2Waxing...
In order to maintain the appearance of your ve-hicle, it is important to take proper care of it.To protect the paint surfaces, please wash yourvehicle
REMOVING SPOTSRemove tar and oil spots, industrial dust, insects,and tree sap as quickly as possible from thesurface of the paint to avoid lasting dam
● Do not apply wheel cleaners to thewheels when they are hot. The wheeltemperature should be the same as am-bient temperature.● Rinse the wheel to com
CAUTION● Never use benzine, thinner or any simi-lar material.● Small dirt particles can be abrasive anddamaging to leather surfaces andshould be remov
SEAT BELTSThe seat belts can be cleaned by wiping themwith a sponge dampened in a mild soap solution.Allow the belts to dry completely in the shadebef
PREGNANT WOMENNISSAN recommends that pregnant women useseat belts. The seat belt should be worn snug andalways position the lap belt as low as possibl
CAUTION● NEVER remove dirt, sand or other de-bris from the passenger compartmentby washing it out with a hose. Removedirt with a vacuum cleaner or bro
MEMO7-8 Appearance and care
8 Maintenance and do-it-yourselfMaintenance requirements...8-2General maintenance ...8-2Explanation
Your NISSAN has been designed to have mini-mum maintenance requirements with long ser-vice intervals to save you both time and money.However, some day
When driving in areas using road salt or othercorrosive materials, check lubrication frequently.Lights* Clean the headlights on a regular basis.Make s
Seat belts Check that all parts of the seat beltsystem (for example, buckles, anchors, adjustersand retractors) operate properly and smoothly,and are
Underbody The underbody is frequently ex-posed to corrosive substances such as thoseused on icy roads or to control dust. It is veryimportant to remov
CAUTION● Do not work under the hood while theengine is hot. Turn the engine off andwait until it cools down.● Avoid contact with used engine oil andco
1. Power steering fluid reservoir2. Engine oil filler cap3. Brake fluid reservoir4. Air cleaner5. Fuse block/ Fusible links6. Battery7. Fusible links8
The engine cooling system is filled at the factorywith a pre-diluted mixture of 50% GenuineNISSAN Long Life Antifreeze/Coolant (blue) and50% water to
Fastening the seat belts䊊1Adjust the seat. See “Seats” earlier in thissection.䊊2Slowly pull the seat belt out of the retractorand insert the tongue in
CHECKING ENGINE COOLANTLEVELCheck the coolant level in the reservoir whenthe engine is cold. If the coolant level is belowthe MIN level䊊B, add coolant
CHECKING ENGINE OIL LEVEL1. Park the vehicle on a level surface and applythe parking brake.2. Start the engine and let it idle until it reachesoperati
CHANGING ENGINE OIL1. Park the vehicle on a level surface and applythe parking brake.2. Start the engine and let it idle until it reachesoperating tem
CHANGING ENGINE OIL FILTER1. Park the vehicle on a level surface and applythe parking brake.2. Turn the engine off.3. Place a large drain pan under th
The fluid level should be checked using the HOTMAX range on the power steering fluid reservoirat fluid temperatures of 122° - 176°F (50° -80°C) or usi
BRAKE FLUIDCheck the brake fluid level in the reservoir. If thefluid level is below the MIN line or the brakewarning light comes on, add Genuine NISSA
● Keep the battery surface clean and dry.Clean the battery with a solution of bakingsoda and water.● Make certain the terminal connections areclean an
1. Remove the vent caps with a screwdriver asshown. Use a cloth to protect the batterycase.2. Check the fluid level in each cell. If it isnecessary to
CAUTION● Do not ground accessories directly tothe battery terminal. Doing so will by-pass the variable voltage control sys-tem and the vehicle battery
2. Have the belt checked regularly for condi-tion and tension in accordance with themaintenance schedule found in the“NISSAN Service and Maintenance G
䊊3Position the lap belt portion low and snugon the hips as shown.䊊4Pull the shoulder belt portion toward theretractor to take up extra slack. Be sure
The air cleaner filter should not be cleaned andreused. Replace it according to the maintenancelog shown in the “NISSAN Service and Mainte-nance Guide
CLEANINGIf your windshield is not clear after using thewindshield-washer or if a wiper blade chatterswhen running, wax or other material may be onthe
Be careful not to let anything get into the washernozzle䊊A. This may cause clogging or improperwindshield washer operation. If something getsinto the
Two types of fuses are used. Type䊊Ais used inthe fuse boxes in the engine compartment. Type䊊Bis used in the passenger compartment fusebox.Type A fuses
If any electrical equipment does not come on,check for an open fuse.1. Be sure the ignition switch and the headlightswitch are OFF.2. Open the engine
Fusible linksIf the electrical equipment does not operate andfuses are in good condition, check the fusiblelinks. If any of these fusible links are me
Extended storage switchIf any electrical equipment does not operate,remove the extended storage switch and checkfor an open fuse.NOTE:The extended sto
CAUTIONBe careful not to allow children to swallowthe battery or removed parts.NISSAN INTELLIGENT KEY®Replace the battery in the Intelligent Key as fo
or modifications not expressly approved bythe party responsible for compliance couldvoid the user’s authority to operate theequipment.For Canada:This
FRONT PARK/TURN/SIDEMARKERLIGHTBulb replacement requires the removal of theheadlight assembly. If replacement is required,see your NISSAN dealer.FOG L
To increase your confidence in the seat belts,check the operation as follows:● Grasp the shoulder belt and pull forwardquickly. The retractor should l
1. Headlight assembly2. Map light3. Rear personal lights4. Door mirror turn signal light(if so equipped)5. Step light6. Fog light (if so equipped)7. H
Replacement proceduresAll other lights are either type A, B, C or D. Whenreplacing a bulb, first remove the lens, lampand/or cover.Indicates bulb remo
Use a cloth䊊1to protect the housing. Use a cloth䊊1to protect the housing.Step lightLDI0341Personal lightWDI0670Trunk lightLDI2135Maintenance and do-it
If you have a flat tire, see “Flat tire” in the“In case of emergency” section of thismanual.TIRE PRESSURETire Pressure Monitoring System(TPMS)This veh
Incorrect tire pressure, including un-der inflation, may adversely affecttire life and vehicle handling.WARNING● Improperly inflated tires can failsud
Tire and loading information label䊊1Seating capacity: The maximum num-ber of occupants that can be seatedin the vehicle.䊊2Vehicle load limit: See load
Checking tire pressure1. Remove the valve stem cap from thetire.2. Press the pressure gauge squarelyonto the valve stem. Do not press toohard or force
Size Cold Tire Inflation Pres-sureFront Original TireP245/45VR18 230 kPa, 33 PSIP245/40VR19 230 kPa, 33 PSI245/40WR19 230 kPa, 33 PSIRear Original Tir
䊊1Tire size (example: P215/65R15 95H)1. P: The “P” indicates the tire is de-signed for passenger vehicles (not alltires have this information).2. Thre
䊊2TIN (Tire Identification Number) for anew tire (example: DOT XX XX XXXXXXX)1. DOT: Abbreviation for the “Depart-ment Of Transportation”. The symbolc
WARNING● Only NISSAN seat belt extenders, madeby the same company which made theoriginal equipment seat belts, shouldbe used with NISSAN seat belts.●
䊊7The word “radial”The word “radial” is shown if the tire hasradial structure.䊊8Manufacturer or brand nameManufacturer or brand name is shown.Other Ti
For additional traction on icy roads, studded tiresmay be used. However, some U.S. states andCanadian provinces prohibit their use. Checklocal, state
Wheel nut tightening torque:83 ft-lb (112 N·m)The wheel nuts must be kept tight-ened to specifications at all times. Itis recommended that wheel nuts
Replacing wheels and tiresWhen replacing a tire, use the same size, treaddesign, speed rating and load carrying capacityas originally equipped. Recomm
Care of wheels● Wash the wheels when washing the vehicleto maintain their appearance.● Clean the inner side of the wheels when thewheel is changed or
MEMO8-44 Maintenance and do-it-yourself
9 Technical and consumer informationCapacities and recommended fuel/lubricants ...9-2Fuel Recommendation ...9-3Engine oil
The following are approximate capacities. The actual refill capacities may be slightly different. When refilling, follow the proceduredescribed in the
FUEL RECOMMENDATIONNISSAN recommends the use of unleaded pre-mium gasoline with an octane rating of at least91 AKI (Anti-Knock Index) number (Research
● If a methanol blend is used, it shouldcontain no more than 5% methanol(methyl alcohol, wood alcohol). Itshould also contain a suitable amountof appr
If you see this symbol, it means “Do not do this”or “Do not let this happen.”If you see a symbol similar to these in an illustra-tion, it means the ar
There are three basic types of child restraintsystems:● Rear-facing child restraint● Forward-facing child restraint● Booster seatThe proper restraint
ENGINE OIL AND OIL FILTERRECOMMENDATIONSSelecting the correct oilIt is essential to choose the correct grade, qualityand viscosity engine oil to ensur
Your engine was filled with a high-quality engineoil when it was built. You do not have to changethe oil before the first recommended changeinterval.
ENGINEModel VQ35DEType Gasoline, 4-cycle, DOHCCylinder arrangement 6-cylinder, V-block, Slanted at 60°Bore x Stroke in (mm) 3.760 x 3.205 (95.5 x 81.4
WHEELS AND TIRESWheels Size Offset in (mm)18 x 8.0JJ 1.97 (50)19 x 8.0JJ 1.97 (50)TiresP245/45VR18P245/40VR19245/40WR19Spare tire T145/80D17Speed rati
When planning to drive your NISSAN ve-hicle in another country, you should first findout if the fuel available is suitable for your vehi-cle’s engine.
ENGINE SERIAL NUMBERThe number is stamped on the engine as shown.F.M.V.S.S./C.M.V.S.S.CERTIFICATION LABELThe Federal/Canadian Motor Vehicle SafetyStan
TIRE AND LOADING INFORMATIONLABELThe cold tire pressure is shown on the Tire andLoading Information label. The label is located asshown.AIR CONDITIONE
WARNING● It is extremely dangerous to ridein a cargo area inside a vehicle. Ina collision, people riding in theseareas are more likely to be seri-ousl
VEHICLE LOAD CAPACITYDo not exceed the load limit of your ve-hicle shown as “The combined weight ofoccupants and cargo” on the Tire andLoading Informa
Steps for determining correct loadlimit1. Locate the statement “The combinedweight of occupants and cargoshould never exceed XXX lbs or XXXkg” on your
Once a child outgrows the height or weight limitof the harness-equipped forward-facing child re-straint, NISSAN recommends that the child beplaced in
5. Determine the combined weight ofluggage and cargo being loaded onthe vehicle. That weight may notsafely exceed the available cargo andluggage load
WARNINGOverloading or improper loading of atrailer and its cargo can adversely affectvehicle handling, braking and perfor-mance and may lead to accide
Temperature conditions also can affect towing.For example, towing a heavy trailer in high outsidetemperatures on graded roads can affect engineperform
Maximum Gross Vehicle Weight(GVW)/maximum Gross Axle Weight(GAW)The GVW of the towing vehicle must not exceedthe Gross Vehicle Weight Rating (GVWR)sho
4,546 lb. (2062 kg) GVWR– 4,446 lb. (2016 kg) GVW= 100 lb. (45 kg) Available for tongueweight1,000 lb. (454 kg) Capacity available fortowing100 lb. (4
Ball mountThe hitch ball is attached to the ball mount andthe ball mount is inserted into the hitch receiver.Choose a proper class ball mount based on
Trailer lightsCAUTIONWhen splicing into the vehicle electricalsystem, a commercially available power-type module/converter must be used toprovide powe
● When backing up, hold the bottom of thesteering wheel with one hand. Move yourhand in the direction in which you want thetrailer to go. Make small c
2. When the trailer sway stops, gently apply thebrakes and pull to the side of the road in asafe area.3. Try to rearrange the trailer load so it is ba
DOT (Department of Transportation) QualityGrades: All passenger car tires must conform tofederal safety requirements in addition to thesegrades.Qualit
– Infants and children should never beheld on anyone’s lap. Even the stron-gest adult cannot resist the forces ofa collision.– Do not put a seat belt
For USAIf you believe that your vehicle has a de-fect which could cause a crash or couldcause injury or death, you should immedi-ately inform the Nati
Due to legal requirements in some states andCanadian Provinces, your vehicle may be re-quired to be in what is called the “ready condi-tion” for an In
Genuine NISSAN Service Manuals for this modelyear and prior can be purchased. A genuineNISSAN Service Manual is the best source ofservice and repair i
MEMO9-28 Technical and consumer information
10 IndexAActive Head Restraint...1-8,1-15Air bag (See supplemental restraintsystem)...1-43Air bag systemFront (See supplemen
Child safety rear door lock ...3-6Chimes, audible reminders ...2-16Cleaning exterior and interior ...7-2C.M.V.S.S. certificat
FuelCapacities and recommendedfuel/lubricants ...9-2Fuel economy ...5-22Fuel-filler door and cap ...3-21Fuel gauge
License plateInstalling the license plate...9-11LightAirbagwarninglight...1-57,2-14Brakelight(Seestoplight)...8-28Bulb check/instru
Precautions on supplemental restraintsystem...1-43Precautions when starting and driving ...5-2Push starting ...6-10R
Rear window and outside mirror defrosterswitch...2-29Turnsignalswitch...2-34Vehicle dynamic control (VDC) offswitch...
All U.S. states and Canadian provinces orterritories require that infants and smallchildren be restrained in an approved childrestraint at all times w
When traveling or registering your vehicle inanother country ...9-9WindowsLocking passengers’ windows ...2-45Power rear windows ...
RECOMMENDED FUEL:NISSAN recommends the use of unleaded pre-mium gasoline with an octane rating of at least91 AKI (Anti-Knock Index) number (Researchoc
®2014 MAXIMAOWNER’S MANUALFor your safety, read carefully and keep in this vehicle.2014 NISSAN MAXIMA A35-D Printing : July 2013 (13)Publicatio
– Child restraint anchorages are de-signed to withstand only those loadsimposed by correctly fitted child re-straints. Under no circumstances arethey
When installing a child restraint, carefully readand follow the instructions in this manual andthose supplied with the child restraint.Top tether anch
2. Secure the child restraint anchor attach-ments to the LATCH lower anchors. Checkto make sure the LATCH attachment is prop-erly attached to the lowe
4. After attaching the child restraint, test it be-fore you place the child in it. Push it from sideto side while holding the child restraint nearthe
WARNINGThe three-point seat belt with AutomaticLocking Retractor (ALR) must be usedwhen installing a child restraint. Failure touse the ALR mode will
3. Pull the shoulder belt until the belt is fullyextended. At this time, the seat belt retractoris in the Automatic Locking Retractor (ALR)mode (child
NISSAN CARES...Both NISSAN and your NISSAN dealer are dedicated to serving all your automotive needs. Your satisfaction with your vehicle and your NIS
6. After attaching the child restraint, test it be-fore you place the child in it. Push it from sideto side while holding the child restraint nearthe
3. The back of the child restraint should besecured against the vehicle seatback.If necessary, adjust or remove the headrestraint/headrest to obtain t
6. After attaching the child restraint, test it be-fore you place the child in it. Push it from sideto side while holding the child restraint nearthe
2. Position the child restraint on the seat. Al-ways follow the child restraint manufactur-er’s instructions.The back of the child restraint should be
5. Allow the seat belt to retract. Pull up on theshoulder belt to remove any slack in the belt.6. Remove any additional slack from the seatbelt; press
9. Check to make sure the child restraint isproperly secured prior to each use. If theseat belt is not locked, repeat steps 3through 8.10. If the chil
4. Refer to the appropriate child restraint in-stallation procedure steps in this sectionbefore tightening the tether strap.If you have any questions
Booster seats of various sizes are offered byseveral manufacturers. When selecting anybooster seat, keep the following points in mind:● Choose only a
1. If you must install a booster seat in thefront seat, move the seat to the rear-most position.2. Position the booster seat on the seat. Onlyplace it
7. If the booster seat is installed in the frontpassenger seat, place the ignition switch inthe ON position. The front passenger air bagstatus lightma
Table ofContentsIllustrated table of contentsSafety—Seats, seat belts and supplemental restraint systemInstruments and controlsPre-driving checks and
WARNING● The front air bags ordinarily will notinflate in the event of a side impact, rearimpact, rollover, or lower severity fron-tal collision. Alwa
WARNING● Never let children ride unrestrained orextend their hands or face out of thewindow. Do not attempt to hold them inyour lap or arms. Some exam
WARNING● Children may be severely injured orkilled when the front air bags, side airbags or curtain air bags inflate if theyare not properly restraine
WARNING● Even with the NISSAN Advanced AirBag System, never install a rear-facingchild restraint in the front seat. An in-flating front air bag could
WARNING● The seat belts, the side air bags andcurtain air bags are most effective whenyou are sitting well back and upright inthe seat with both feet
SSS0159 SSS01621-48 Safety—Seats, seat belts and supplemental restraint system
1. Roof-mounted curtain side-impactsupplemental air bag inflators2. Roof-mounted curtain side-impactsupplemental air bags3. Front seat-mounted side-im
The NISSAN Advanced Air Bag System has dualstage inflators. It also monitors information fromthe crash zone sensor, the Air Bag Control Unit(ACU), sea
Front passenger air bag and status lightWARNINGThe front passenger air bag is designed toautomatically turn OFF under some condi-tions. Read this sect
Front passenger seat adult occupants who areproperly seated and using the seat belt as outlinedin this manual should not cause the passenger airbag to
Other supplemental front-impact air bagprecautionsWARNING● Do not place any objects on the steeringwheel pad or on the instrument panel.Also, do not p
Front seat-mounted side-impactsupplemental air bag and roof-mounted curtain side-impactsupplemental air bag systemsThe side air bags are located in th
● No unauthorized changes should bemade to any components or wiring ofthe side air bag and curtain air bagsystems. This is to prevent damage to oracci
After pretensioner activation, load limiters allowthe seat belt to release webbing (if necessary) toreduce forces against the chest.The supplemental a
If any of the following conditions occur, the frontair bag, side air bag, curtain air bag and preten-sioner systems need servicing:● The supplemental
2 Instruments and controlsInstrument panel...2-2Meters and gauges ...2-3Speedometer and o
Moonroof (if so equipped) ...2-46Power moonroof...2-46Dual Panel Moonroof (if so equipped)...
1. Side and center vents (P. 4-28)2. Headlight/fog light (if so equipped)/turnsignal switch (P. 2-30)3. Steering wheel switch for audio controland Blu
24. Vehicle Dynamic Control (VDC) OFFswitch (P. 2-37)Outside mirror controls (P. 3-27)Heated steering wheel switch(if so equipped) (P. 2-37)Trunk lid
SPEEDOMETER AND ODOMETERSpeedometerThe speedometer indicates the vehicle speed.Odometer/Twin trip odometerThe odometer/twin trip odometer is displayed
0 Illustrated table of contentsAir bags, seat belts and child restraints ...0-2Exterior front ...0-3Exte
TACHOMETERThe tachometer indicates engine speed in revo-lutions per minute (RPM). Do not rev the engineinto the red zone䊊1.CAUTIONWhen engine speed ap
FUEL GAUGEThe gauge indicates the approximate fuel levelin the tank.The gauge may move slightly during braking,turning, acceleration, or going up or d
COMPASS DISPLAYPush the button for about 1 second whenthe ignition switch is placed in the ON position totoggle the outside temperature and compassdir
Zone variation change procedureThe difference between magnetic north and geo-graphical north is known as variance. In someareas, this difference can s
1. With the display turned on, press and holdthefor about 10 seconds. The “C”icon in the compass display will illuminate.2. Calibrate the compass by d
or Anti-lock Braking System (ABS)warning lightSupplemental air bag warning light Malfunction Indicator Light (MIL)or Brake warning lightContinuously V
or Anti-lock BrakingSystem (ABS)warning lightWhen the ignition switch is placed in the ONposition, the Anti-lock Braking System (ABS)warning light ill
CAUTION● Do not ground electrical accessories di-rectly to the battery terminal. Doing sowill bypass the variable control systemand the vehicle batter
TPMS malfunction:If the TPMS is not functioning properly, the lowtire pressure warning light will flash for approxi-mately 1 minute when the ignition
Master warning lightWhen the ignition is in the ON position, themaster warning light illuminates if any of the fol-lowing are displayed on the vehicle
1. Top tether strap anchor (P. 1-38)2. Rear head restraints/headrests (P. 1-7)3. Rear seat belts (P. 1-15)4. Roof-mounted curtain side-impactsupplemen
Continuously VariableTransmission (CVT) positionindicator lightWhen the ignition switch is placed in the ONposition, the indicator light shows the shi
● Malfunction indicator light blinking — An en-gine misfire has been detected which maydamage the emission control system. To re-duce or avoid emissio
AUDIBLE REMINDERSBrake pad wear warningThe disc brake pads have audible wear warnings.When a disc brake pad requires replacement, itmakes a high pitch
HOW TO USE THE VEHICLEINFORMATION DISPLAYPress thebutton, located on the instru-ment panel just behind the steering wheel, todisplay the following mod
Time/Miles (km) modeThe time/miles (km) mode can be selected toshow the time and distance driven since the lastreset.Range modeThe range mode can be s
In case of a low tire pressure, a warning messagewill also appear in the vehicle information display.See “Check tire pressure warning” later in thisse
Alert modeThe alert mode allows you to set alerts notifyingyou of time to rest or icy conditions.The time to rest alert lets you know when youhave bee
Options modeThe LANGUAGE/UNIT/EFFECTS screen willappear when selecting the“Language/Unit/Effects” key andpressing.Language: English, French or Spanish
Vehicle information display warningsand indicators1. Door and trunk open warning2. Push warning3. Low fuel warning4. Low windshield-washer fluid warni
12. Loose fuel cap warning13. Check tire pressure warning14. Tire pressure warning15. I-Key System Error: See Owner’s ManualDoor and trunk open warnin
Commentaires sur ces manuels